Klein-tools VDV501-090 Manuale Utente Pagina 11
- Pagina / 44
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
11
2.
Note that the connection to the cable to be tested should be as
short as possible to ensure the Ranger™ TDR does not see the
impedance continuity at the attachment point as a fault.
3.
Determine the correct NVP value for the cable to be tested as
instructed in
Obtaining NVP Values
section.
Obtaining NVP Values section.Obtaining NVP Values
4.
Set the NVP value as instructed in
Setting NVP Values
section.
Setting NVP Values section.Setting NVP Values
5.
Turn the unit on by pressing the Power button.
6.
Change the unit of measurement if necessary by pressing and
holding the Memory and Calibration buttons at the same time.
7.
Press the Test button once. After a moment, the calculated length of
the cable will appear in the upper right hand corner of the screen.
8.
The screen will display "Short" if the two conductors are directly
connected or have a low resistance connection between them.
The length will be shown up to the shorted point.
9.
The screen will display "Open" if the two conductors are not
directly connected or have a high resistance connection between
them. This is the normal condition for performing length testing.
If there is an unexpected open condition along the length of the
cable, only the length up to that point will be displayed.
10.
The screen will display "Error" and show dashes instead of the
length if an error condition has occurred. This could be because
the cable is improperly terminated or there has been excessive
signal loss.
Step 7
Step 10
•
Using Loop Testing Mode:
The Ranger™ TDR can run continuous tests when set to Loop Mode.
Loop Mode can help when testing long cable runs susceptible to
signal loss, and enabling you to test multiple cables without having to
press the Test button each time.
1.
While in Test Mode, press and hold the Test button.
2.
The screen will momentarily fl ash "LOOP", then run a test every
two seconds and display the results.
3.
Pressing any other button except the Power button exits
Loop Mode.
- Instruction 1
- FEATURES 2
- GENERAL SPECIFICATIONS 2
- WARNINGS 3
- OVERVIEW 4
- ACCESSORIES 5
- LCD SCREEN ICONS 6
- STARTUP AND SHUTDOWN 8
- GENERAL TESTING PROCEDURES 8
- OBTAINING NVP VALUES 9
- SETTING NVP VALUES 10
- TONING CABLE 12
- COMMON NVP VALUES 13
- KLEIN TOOLS, INC 14
- Manual de 15
- CARACTERÍSTICAS 16
- ESPECIFICACIONES GENERALES 16
- ADVERTENCIAS 17
- GENERALIDADES 18
- ACCESORIOS 19
- ICONOS DE LA PANTALLA DE LCD 20
- ARRANQUE Y PARADA 22
- AJUSTE DE LOS VALORES DE VPN 24
- GENERACIÓN DE TONOS EN CABLE 26
- VALORES COMUNES DE VPN 27
- REEMPLAZO DE LAS PILAS 27
- GARANTÍA 28
- LIMPIEZA 28
- ALMACENAMIENTO 28
- ELIMINACIÓN / RECICLAJE 28
- SERVICIO AL CLIENTE 28
- Mode d’emploi 29
- FRANÇAIS 30
- AVERTISSEMENTS 31
- ACCESSOIRES 33
- OBTENTION DES VALEURS DE VPN 37
- VALEURS COMMUNES VPN 41
- REMPLACEMENT DES PILES 41
- NOTES / NOTAS / NOTEZ 43
- CUSTOMER SERVICE 44
Prodotti e manuali riguardandi Strumenti di misura Klein-tools VDV501-090
(20 pagine)
PURSUIT 3070 Center Console manuals
Owner’s manuals and user’s guides for Motorhomes PURSUIT 3070 Center Console.
We providing 1 pdf manuals PURSUIT 3070 Center Console for download free by document types: Owner's Manual
Commenti su questo manuale